| Text | The scope of this test is to ensure that riscv64+licheerv image boots from SD card on LicheeRV board
- Flash downloaded image onto SD card
- You can use Gnome Disks app to restore img.xz onto the SD card
- Alternatively you can use xz -d to decompress, and then dd to copy the image to the SD card
- Connect serial console to the board
- FTDI adapter for serial console (pinout available here: https://popolon.org/depots/RISC-V/D1/LicheeRV/dl.sipeed.com/Lichee_RV_Do...)
- Connect to the serial console
- sudo screen /dev/ttyUSB1 115200
- Power on the board
- You should see U-BOOT menu
- It should then boot GRUB after a delay
- You should see GRUB menu
- It should then boot the default kernel after a delay
- After a while cloud-init will run
- Then one will be able to login
- Login and change password
- Login using ubuntu for both username and password
- Reenter ubuntu password again
- Set new password
- Confirm the new password
- Perform Wifi testing
- Make sure licheerv-rtl8723ds-dkms is installed, otherwise, install it:
- $ sudo apt install licheerv-rtl8723ds-dkms
- It will take quite some time to build, the output of the above command should look like this:.
- Preparing to unpack licheerv-rtl8723ds-dkms
- Module licheerv-rtl8723ds-1.0 for kernel 5.17.0-1003-allwinner
- Unpacking licheerv-rtl8723ds-dkms (1.0-0ubuntu1) ...
- Setting up licheerv-rtl8723ds-dkms (1.0-0ubuntu1) ...
- Loading new licheerv-rtl8723ds-1.0 DKMS files...
- Building for 5.17.0-1003-allwinner
- Building initial module for 5.17.0-1003-allwinner
- Done.
- 8723ds.ko:
- Running module version sanity check.
- - Original module
- - No original module exists within this kernel
- - Installation
- - Installing to /lib/modules/5.17.0-1003-allwinner/updates/dkms/
- depmod........................
- You should see a wlan0 interface by typing:
- $ ip a
- 1: lo: mtu 65536 qdisc noqueue state UNKNOWN group defaul0
- link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
- inet 127.0.0.1/8 scope host lo
- valid_lft forever preferred_lft forever
- inet6 ::1/128 scope host
- valid_lft forever preferred_lft forever
- 2: usb0: mtu 1500 qdisc pfifo_fast state DOW0
- link/ether ae:12:05:64:8e:2c brd ff:ff:ff:ff:ff:ff
- 3: wlan0: mtu 1500 qdisc mq state UP group def0
- link/ether 34:20:03:2a:0d:0c brd ff:ff:ff:ff:ff:ff
- inet 192.168.1.28/24 metric 600 brd 192.168.1.255 scope global dynamic wlan0
- valid_lft 86393sec preferred_lft 86393sec
- inet6 fe80::3620:3ff:fe2a:d0c/64 scope link
- valid_lft forever preferred_lft forever
- Try to connect to local network by using the following netplan configuration file saved at /etc/netplan/wifi.yaml
- network:
- version: 2
- renderer: networkd
- wifis:
- wlan0:
- dhcp4: yes
- dhcp6: yes
- access-points:
- "YOUR_SSID":
- password: "YOUR_PASSWORD"
- And then type:
- $ sudo netplan apply
- You should connect successfully to your local network in a few seconds
- Perform generic testing
- Check that apt update works
- Run any command that is not installed, check that command-not-found recommends things to install
- e.g. hello
- Install a package and check that it works, e.g. hello
- Perform snap testing
- Install a snap and check that it works, e.g. hello
- Perform HDMI testing
- Plug an HDMI cable and make sure a prompt asking for login appears on the screen
- Perform USB test
- Plug a keyboard in and enter the login/password
- Reboot
- The board should reboot normally
- Poweroff
- Console messages should reach poweroff target
- There should be final kernel dmsg powering off
- Manually turn power-off from the board
If all actions produce the expected results listed, please submit a 'passed' result.
If an action fails, or produces an unexpected result, please submit a 'failed' result and file a bug. Please be sure to include the bug number when you submit your result.
|
