RaspberryPi 3A+ Post-install in Ubuntu Server armhf+raspi in Noble Daily (archived)

This test case is to be carried out on a Raspberry Pi 3A+.
Follow the installation steps at
IoT installation media

After powering on the machine, look at the power LED

The power LED illuminates and stays illuminated while the kernel continues
to boot.

After logging in, run systemctl status, and look at the
"State:" reported at the top of the output

State should be reported as "running". In particular, it should
not read "degraded".

Run sudo flash-kernel

Exit code is clean (0) and no error messages are reported

Run sudo reboot

System reboots successfully to a login prompt

Run sudo shutdown -h now

System shuts down in a reasonable time (less than a minute)

Check output of free -h

Reported "Mem" under "total" is consistent with a
Raspberry Pi 3A+. It should be in the region of 300-500MB.

Perform a large (300-600MB) file copy to USB storage

• Generate a large (500MB) file: dd if=/dev/urandom of=rubbish
bs=1M count=500
• Insert a USB stick (appropriately sized) into a spare USB port
• Make a mount directory: sudo mkdir /mnt/stick
• Mount the stick: sudo mount /dev/sda1 /mnt/stick
  (modify mount-point as necessary; check sudo dmesg
  output if unsure)
• Copy the file: sudo cp rubbish /mnt/stick/
• Unmount the stick: sudo umount /mnt/stick
• Remove the stick from the USB port
• Re-insert the stick into the USB port
• Re-mount the stick: sudo mount /dev/sda1 /mnt/stick
  (again, adjust mount-point as necessary)
• Compare the copied file to that on the stick: cmp rubbish
/mnt/stick/rubbish

cmp returns 0 and outputs nothing, indicating the files are
identical

Connect a USB keyboard to one of the USB2 ports

Verify that keys typed on the keyboard appear on the console

With an HDMI monitor that supports audio, and an available MP3 file:

• Install ffmpeg and amixer with sudo apt install ffmpeg
alsa-utils
• Find the correct card name for the HDMI port:
  cat /proc/asound/cards and note the name in [brackets]
  for the HDMI port
• Attempt to play your MP3 file with: ffmpeg -i
music.mp3 -f alsa default:CARD=name
  substituting name for the card name found during the
  previous step, and music.mp3 for your choice of MP3 file,
  e.g. mpg321 -o alsa -a hw:0,0 "Jeff Wayne - War of the
Worlds.mp3"
• Use Ctrl+C or q to end playback early, if you
  wish
• If you cannot hear anything, first check that the mixer's volume is
  not set too low; run alsamixer, and adjust the volume
  (J for down, K for up) before exiting
  (Esc) and retrying playback

Audio can be heard through the device

With a pair of headphones with a 3.5mm jack, and an available MP3 file:

• Install ffmpeg and amixer with sudo apt install ffmpeg
alsa-utils
• Find the correct card name for the headphone jack:
  cat /proc/asound/cards and note the name in [brackets]
  for the headphone jack
• Attempt to play your MP3 file with: ffmpeg -i
music.mp3 -f alsa default:CARD=name
  substituting name for the card name found during the
  previous step, and music.mp3 for your choice of MP3 file,
  e.g. mpg321 -o alsa -a hw:0,0 "Jeff Wayne - War of the
Worlds.mp3"
• Use Ctrl+C or q to end playback early, if you
  wish
• If you cannot hear anything, first check that the mixer's volume is
  not set too low; run alsamixer, and adjust the volume
  (J for down, K for up) before exiting
  (Esc) and retrying playback

Audio can be heard through the device

Configure wifi via netplan

• Place the following in /etc/netplan/wifi.yaml
  (substituting the SSID and password as necessary):

•       network:
          version: 2
            wifis:
              wlan0:
                dhcp4: true
                access-points:
                  my-ssid-here:
                    password: my-password-here

• Run sudo netplan apply
• Wait a few seconds (to allow DHCP to complete), then run ip
addr
• Check that a valid IP address is recorded on the wlan0 interface
• Check ping google.com successfully pings a few times
  (Ctrl+C to cancel)

The "wlan0" interface should have a DHCP
assigned IP address and you should be able to ping google.com

Configure bluetooth, scan for, and pair, a device

• Install bluez with sudo apt install bluez
• Run sudo bluetoothctl
• Check bluetoothctl prints Agent registered
• Check the MAC address looks "real" (not some obviously blank
  value like AA:AA:AA:AA:AA:AA)
• Run scan on
• Make some other Bluetooth device visible for pairing (e.g. go into
  Bluetooth settings on your Android phone)
• Verify the other Bluetooth device appears in console output
• Run pair XX:XX:XX:XX:XX:XX
  where XX:XX:XX:XX:XX:XX is the other device's MAC address, as it
  appears in scan output
• Verify the passcode on both devices
• Check output includes "Pairing successful"
• Disable scanning with scan off
• Exit tool with quit

The Bluetooth interface should have a valid MAC address (not
AA:AA:AA:AA:AA:AA), can see and pair with another Bluetooth device.

If all actions produce the expected results listed,
please submit a 'passed' result.
If any action fails, or produces an unexpected result,
please submit a 'failed' result and file a bug. Please be sure to include
the bug number when you submit your
result.