RaspberryPi 3B Post-install in Ubuntu Server armhf+raspi2 in Xenial 16.04.4 (archived)

DownloadLink to the download information
RaspberryPi 3B Post-installDetailed information on the testcase
Testcase (Report an issue with this testcase)

This test case is to be carried out on a Raspberry Pi 3B.
Follow the installation steps at
IoT installation media

After powering on the machine, look at the power LED
The power LED illuminates and stays illuminated while the kernel continues
to boot.
After logging in, run systemctl status, and look at the
"State:" reported at the top of the output
State should be reported as "running". In particular, it should
not read "degraded".
Run sudo flash-kernel
Exit code is clean (0) and no error messages are reported
Run sudo reboot
System reboots successfully to a login prompt
Run sudo shutdown -h now
System shuts down in a reasonable time (less than a minute)
Check output of free -h
Reported "Mem" under "total" is consistent with a
Raspberry Pi 3B. It should be in the region of 800-1000MB.
Perform a large (300-600MB) file copy to USB storage
  • Generate a large (500MB) file: dd if=/dev/urandom of=rubbish
    bs=1M count=500
  • Insert a USB stick (appropriately sized) into a spare USB port
  • Make a mount directory: sudo mkdir /mnt/stick
  • Mount the stick: sudo mount /dev/sda1 /mnt/stick
    (modify mount-point as necessary; check sudo dmesg
    output if unsure)
  • Copy the file: sudo cp rubbish /mnt/stick/
  • Unmount the stick: sudo umount /mnt/stick
  • Remove the stick from the USB port
  • Re-insert the stick into the USB port
  • Re-mount the stick: sudo mount /dev/sda1 /mnt/stick
    (again, adjust mount-point as necessary)
  • Compare the copied file to that on the stick: cmp rubbish
    /mnt/stick/rubbish
cmp returns 0 and outputs nothing, indicating the files are
identical
Connect a USB keyboard to one of the USB2 ports
Verify that keys typed on the keyboard appear on the console
With an HDMI monitor that supports audio, and an available MP3 file:
  • Install ffmpeg and amixer with sudo apt install ffmpeg
    alsa-utils
  • Find the correct card name for the HDMI port:
    cat /proc/asound/cards and note the name in [brackets]
    for the HDMI port
  • Attempt to play your MP3 file with: ffmpeg -i
    music.mp3 -f alsa default:CARD=name

    substituting name for the card name found during the
    previous step, and music.mp3 for your choice of MP3 file,
    e.g. mpg321 -o alsa -a hw:0,0 "Jeff Wayne - War of the
    Worlds.mp3"
  • Use Ctrl+C or q to end playback early, if you
    wish
  • If you cannot hear anything, first check that the mixer's volume is
    not set too low; run alsamixer, and adjust the volume
    (J for down, K for up) before exiting
    (Esc) and retrying playback
Audio can be heard through the device
With a pair of headphones with a 3.5mm jack, and an available MP3 file:
  • Install ffmpeg and amixer with sudo apt install ffmpeg
    alsa-utils
  • Find the correct card name for the headphone jack:
    cat /proc/asound/cards and note the name in [brackets]
    for the headphone jack
  • Attempt to play your MP3 file with: ffmpeg -i
    music.mp3 -f alsa default:CARD=name

    substituting name for the card name found during the
    previous step, and music.mp3 for your choice of MP3 file,
    e.g. mpg321 -o alsa -a hw:0,0 "Jeff Wayne - War of the
    Worlds.mp3"
  • Use Ctrl+C or q to end playback early, if you
    wish
  • If you cannot hear anything, first check that the mixer's volume is
    not set too low; run alsamixer, and adjust the volume
    (J for down, K for up) before exiting
    (Esc) and retrying playback
Audio can be heard through the device
Check auto-configuration of ethernet
  • Run ip addr
  • Check that a valid IP address is recorded on the eth0 interface
  • Check ping google.com successfully pings a few times
    (Ctrl+C to cancel)
The "eth0" interface should have a DHCP
assigned IP address and you should be able to ping google.com
Configure wifi via netplan
  • Place the following in /etc/netplan/wifi.yaml
    (substituting the SSID and password as necessary):
  •       network:
            version: 2
              wifis:
                wlan0:
                  dhcp4: true
                  access-points:
                    my-ssid-here:
                      password: my-password-here
  • Run sudo netplan apply
  • Wait a few seconds (to allow DHCP to complete), then run ip
    addr
  • Check that a valid IP address is recorded on the wlan0 interface
  • Check ping google.com successfully pings a few times
    (Ctrl+C to cancel)
The "wlan0" interface should have a DHCP
assigned IP address and you should be able to ping google.com
Configure bluetooth, scan for, and pair, a device
  • Install bluez with sudo apt install bluez
  • Run sudo bluetoothctl
  • Check bluetoothctl prints Agent registered
  • Check the MAC address looks "real" (not some obviously blank
    value like AA:AA:AA:AA:AA:AA)
  • Run scan on
  • Make some other Bluetooth device visible for pairing (e.g. go into
    Bluetooth settings on your Android phone)
  • Verify the other Bluetooth device appears in console output
  • Run pair XX:XX:XX:XX:XX:XX
    where XX:XX:XX:XX:XX:XX is the other device's MAC address, as it
    appears in scan output
  • Verify the passcode on both devices
  • Check output includes "Pairing successful"
  • Disable scanning with scan off
  • Exit tool with quit
The Bluetooth interface should have a valid MAC address (not
AA:AA:AA:AA:AA:AA), can see and pair with another Bluetooth device.

If all actions produce the expected results listed,
please submit a 'passed' result.
If any action fails, or produces an unexpected result,
please submit a 'failed' result and file a bug. Please be sure to include
the bug number when you submit your
result.

ReporterLast updateBugsComment
Add a test result

You need to be logged in to submit your test results.