Details for testcase: RaspberryPi 5 4GB Desktop SD



BugReport a bug against the content of this testcase
ID1791
TitleRaspberryPi 5 4GB Desktop SD
LinkNo link provided
Part of testsuitesUbuntu Desktop arm64+raspi

RevisionWritten on the 2024-08-28 11:49 by andersson123
Text

This test case is to be carried out on a Raspberry Pi 5 4GB.
Follow the installation steps at
IoT installation media
, and write the image to an SD card.
Then, using sudo rpi-eeprom-config, ensure the EEPROM's
BOOT_ORDER
is set to 0xf1.

Watch the power LED
Ensure it turns on at boot time, and stays lit as the kernel starts
(when the rainbow screen disappears)
Watch the boot screen
Check that the Ubuntu logo, and spinner appear during boot time
Ensure you have speakers on your monitor or headphones plugged into it
Check that the Ubuntu start up sound plays through the monitor's audio
output before the initial System Configuration appears
Select your timezone, and click on the Continue button
The 'Who are you?' screen appears
Input your initial user details and password
admin can not be used - it is a dedicated Linux User
Name, username and password are accepted. Login options and home folder
encryption choices shown
Continue button becomes available
Run sudo flash-kernel
Exit code is clean (0) and no error messages are reported
Click the power icon at the top right of the screen, and expand the "Power
Off / Log Out" entry in the menu that appears, then "Restart..." from that
menu, and confirm "Restart" in the dialog that appears
System reboots successfully to a login prompt
Click the power icon at the top right of the screen, and expand the "Power
Off / Log Out" entry in the menu that appears, then "Power Off..." from
that menu, and confirm "Power Off" in the dialog that appears
System shuts down in a reasonable time (less than a minute)
Launch Settings from
the menu that appears, then "About" in the left panel of the window that
appears
Reported "Memory" is consistent with a Raspberry Pi 5 4GB.
It should be in the region of 3.6-3.8GB.
Check auto-configuration of ethernet
  • Run ip addr
  • Check that a valid IP address is recorded on the eth0 interface
  • Check ping google.com successfully pings a few times
    (Ctrl+C to cancel)
The "eth0" interface should have a DHCP
assigned IP address and you should be able to ping google.com
Configure wifi via Network Manager
  • Launch settings
  • Select the WiFi entry from the menu
  • Select your local WiFi network from the visible networks list
  • Enter the password for your local WiFi network when prompted
  • Wait a few seconds (to allow DHCP to complete), then run ip
    addr
  • Check that a valid IP address is recorded on the wlan0 interface
  • Disconnect ethernet, if any is plugged in
  • Check ping google.com successfully pings a few times
    (Ctrl+C to cancel)
  • Reconnect ethernet, if it was connected before
The "wlan0" interface should have a DHCP
assigned IP address and you should be able to ping google.com
Configure bluetooth and pair a device
  • Launch settings
  • Select the Bluetooth entry from the menu (you must be on this page
    for the Pi to be "discoverable")
  • On another Bluetooth device (e.g. an Android phone) make sure it
    is "discoverable" (e.g. on Android go into Bluetooth
    settings)
  • Ensure the other device shows up in the "Devices" list
    on the Bluetooth settings page, then select it
  • Confirm the pincode on both devices
  • Ensure the other device now shows as anything other that "Not
    Set Up" in the "Devices" list
The Bluetooth interface can scan for, and pair with, another device
Start Firefox and play a YouTube video
  • Ensure you have functioning speakers / a headset plugged into your
    monitor
  • Click on the Firefox icon on the left of the screen
  • Navigate to YouTube
  • Select a video (with audio!) to play
Check the video plays smoothly, and that audio is output through the
monitor, or speakers / headset plugged into the monitor
Download and play BigBuckBunny in the built-in video player
  • Ensure you have functioning speakers / a headset plugged into your
    monitor
  • Start a terminal session
  • Run wget https://archive.org/download/BigBuckBunny_124/Content/big_buck_bunny_720p_surround.mp4
  • Once the download has completed, run totem big_buck_bunny_720p_surround.mp4
  • The utility may prompt to install codecs; accept the recommendation
    and install whatever codecs are required
Check the video plays smoothly, and that audio is output through the
monitor, or speakers / headset plugged into the monitor
Press Super+L and wait for the lock screen to appear, then
fade, then for the monitor to suspend. Move the mouse to wake up the
monitor, then enter your password to unlock the desktop.
Ensure the monitor suspends correctly, that it awakens again correctly,
and that the desktop unlocks successfully (without the system hanging).

If all actions produce the expected results listed,
please submit a 'passed' result.
If any action fails, or produces an unexpected result,
please submit a 'failed' result and file a bug. Please be sure to include
the bug number when you submit your
result.

RevisionWritten on the 2024-04-24 14:26 by andersson123
RevisionWritten on the 2024-04-11 11:05 by andersson123
RevisionWritten on the 2023-10-02 12:09 by andersson123