Details for testcase: RaspberryPi CM3+ Lite Post-install



BugReport a bug against the content of this testcase
ID1727
TitleRaspberryPi CM3+ Lite Post-install
LinkNo link provided
Part of testsuitesARM Server

RevisionWritten on the 2023-09-29 14:45 by brian-murray
Text

This test case is to be carried out on a Raspberry Pi Compute Module 3+ Lite.
Follow the installation steps at
IoT installation media

Run sudo flash-kernel
Exit code is clean (0) and no error messages are reported
Run sudo reboot
System reboots successfully to a login prompt
Run sudo shutdown -h now
System shuts down in a reasonable time (less than a minute)
Check output of free -h
Reported "Mem" under "total" is consistent with a
Raspberry Pi Compute Module 3+ Lite. It should be in the region of 800-1000MB.
Perform a large (300-600MB) file copy to USB storage
  • Generate a large (500MB) file: dd if=/dev/urandom of=rubbish
    bs=1M count=500
  • Insert a USB stick (appropriately sized) into a spare USB port
  • Make a mount directory: sudo mkdir /mnt/stick
  • Mount the stick: sudo mount /dev/sda1 /mnt/stick
    (modify mount-point as necessary; check sudo dmesg
    output if unsure)
  • Copy the file: sudo cp rubbish /mnt/stick/
  • Unmount the stick: sudo umount /mnt/stick
  • Remove the stick from the USB port
  • Re-insert the stick into the USB port
  • Re-mount the stick: sudo mount /dev/sda1 /mnt/stick
    (again, adjust mount-point as necessary)
  • Compare the copied file to that on the stick: cmp rubbish
    /mnt/stick/rubbish
cmp returns 0 and outputs nothing indicating the files are
identical
Connect a USB keyboard to one of the USB2 ports
Verify that keys typed on the keyboard appear on the console
With an HDMI monitor that supports audio, and an available MP3 file:
  • Install mpg321 and amixer with sudo apt install mpg321
    alsa-utils
  • Find the correct hardware output for the HDMI port:
    cat /proc/asound/cards and note the number at the start
    of the line for the HDMI port (usually 0 and possibly
    1 for any connected monitor(s), and 1 or possibly 2 for the headphone
    jack)
  • Attempt to play your MP3 file with: mpg321 -o alsa -a
    hw:num,0 music.mp3
    substituting
    num for the number found during the previous step, and
    music.mp3 for your choice of MP3 file, e.g. mpg321 -o
    alsa -a hw:0,0 "Jeff Wayne - War of the
    Worlds.mp3"
  • Use Ctrl+C to end playback early, if you wish
  • If you cannot hear anything, first check that the mixer's volume is
    not set too low; run alsamixer, and adjust the volume
    (J for down, K for up) before exiting
    (Esc) and retrying playback
Audio can be heard through the device

If all actions produce the expected results listed,
please submit a 'passed' result.
If any action fails, or produces an unexpected result,
please submit a 'failed' result and file a bug. Please be sure to include
the bug number when you submit your
result.

RevisionWritten on the 2021-09-17 19:18 by brian-murray
RevisionWritten on the 2020-10-13 09:26 by paride
RevisionWritten on the 2020-10-13 09:25 by paride
RevisionWritten on the 2020-06-22 16:30 by brian-murray
RevisionWritten on the 2020-06-22 16:27 by brian-murray